Prioritiy

The user is able to define whether the controller should prioritize active or reactive power via the usage of this parameter.
Active power given preference if the total power is more than the converter rating.
Reactive power given preference

Nominal power Pn

VA

Nominal power of the converter in VA. Default is 60000.

Nominal frequency fn

Hz

This parameter allows the user to specify the nominal frequency in hertz. Default is 50.

Q regulator gain Kp

This parameter allows the user to specify the reactive regulator gain Kp. Default is 1.

Q regulator gain Ki

This parameter allows the user to specify the reactive regulator gain Ki. Default is 25.

P regulator gain Kp

This parameter allows the user to specify the active regulator gain Kp. Default is 1.

P regulator gain Ki

This parameter allows the user to specify the active regulator gain Ki. Default is 25.

Current regulator gain Kp

This parameter allows the user to specify the current regulator gain Kp. Default is 1.

Current regulator gain Ki

This parameter allows the user to specify the current regulator gain Ki. Default is 50.

Islanded mode voltage regulator gain Kp

This parameter allows the user to specify the islanded mode voltage regulator gain Kp. Default is 3.

Islanded mode voltage regulator gain Ki

This parameter allows the user to specify the islanded mode voltage regulator gain Ki. Default is 40.

DC voltage regulator enable

This parameter allows the user to specify the DC voltage regulator enable. Default is unchecked.

DC link voltage regulator Kp

This parameter allows the user to specify the DC link voltage regulator Kp. Default is 1.

DC link voltage regulator Ki

This parameter allows the user to specify the DC link voltage regulator Ki. Default is 50.

Current limit

This parameter allows the user to specify the current limit. Default is 1.2.

Sample time

s

This parameter allows the user to specify the block sample time in seconds. Default is 50e-6.

Proportional gain

This parameter enables the user to select the proportional gain for the PI controller in PV mode and grid-connected mode. Default is 1.

Integral gain

This parameter enables the user to select the integral gain for the PI controller in PV mode and grid-connected mode. Default is 5.

Upper limit

This parameter enables the user to select the upper limit for the PI controller in PV mode and grid-connected mode. Default is 1.

Lower limit

This parameter enables the user to select the lower limit for the PI controller in PV mode and grid-connected mode. Default is -1.

Antiwinup gain

This parameter enables the user to select the antiwinup gain for the PI controller in PV mode and grid-connected mode. Default is 1.

Filter type

Specify the type of filter for voltage measurements: Lowpass (default), Highpass, Bandpass , or Bandstop (notch).

Nominal frequency fn

Hz

Specify the natural frequency of the filter for voltage measurements, in hertz. This value must be a scalar or a vector. Default is 1000.

Damping ratio Zeta (Q = 1/(2*Zeta))

Specify the damping ratio of the filter. The damping ratio is typically a value between 0 and 1. Default is 0.707.

Filter type

Specify the type of filter for current measurements: Lowpass (default), Highpass, Bandpass , or Bandstop (notch).

Nominal frequency fn

Hz

Specify the natural frequency of the filter for current measurements, in hertz. This value must be a scalar or a vector. Default is 1000.

Damping ratio Zeta (Q = 1/(2*Zeta))

Specify the damping ratio of the filter for current measurements. The damping ratio is typically a value between 0 and 1. Default is 0.707.

Type

Specify the battery model: Lithium-Ion (default), Lead-Acid, Nickel-Cadmium, Nickel-Metal-Hydride.

Nominal voltage

V

Specify the nominal voltage, Vnom, of the battery, in V. Default is 1200.

Rated capacity

Ah

Specify the rated capacity, Qrated, of the battery, in Ah. The rated capacity is the minimum effective capacity of the battery. Default is 166.67.

Initial state-of-charge

%

Specify of the state-of-charge (SOC) of the battery, expressed as a percentage of the maximum potential charge, at the beginning of simulation. An SOC of 100% indicates a fully charged battery and 0% indicates an empty battery. Default is 60.

Battery response time

s

Specify the response time of the battery, in s, at 95% of the final value. This value represents the voltage dynamics and can be observed when a current step is applied. Default is 0.5.

Determined from the nominal parameters of the battery

Select to have the block determine the parameters in the Discharge settings based on the values specified for the parameters in the Parameters settings: on (default), off. Dependencies: Selecting this parameter disables the parameters in the Discharge settings.

Maximum capacity

Ah

Maximum theoretical capacity, Q, when a discontinuity occurs in the battery voltage, in Ah. This value is generally equal to 105% of the rated capacity. Dependencies: To enable this parameter, in the Parameters settings, set Use a preset battery to no.

Cut-off Voltage

V

Maximum theoretical capacity, Q, when a discontinuity occurs in the battery voltage, in Ah. This value is generally equal to 105% of the rated capacity. Dependencies: To enable this parameter, in the Parameters settings, set Use a preset battery to no.

Fully charged voltage

V

Fully charged voltage, Vfull, for a given discharge current. The fully charged voltage is not the no-load voltage. Dependencies: To enable this parameter, in the Parameters settings, set Use a preset battery to no.

Nominal discharge current

A

Nominal discharge current, in A, for which the discharge curve is measured. Dependencies: To enable this parameter, in the Parameters settings, set Use a preset battery to no.

Internal resistance

Ohms

Internal resistance of the battery, in ohms. When a preset model is used, a generic value is loaded that corresponds to 1% of the nominal power (nominal voltage multiplied by the battery rated capacity). The resistance is constant during the charge and the discharge cycles and does not vary with the amplitude of the current. Dependencies: To enable this parameter, in the Parameters settings, set Use a preset battery to no.

Capacity

Ah

Amp-hour capacity at nominal voltage. Capacity, Qnom, extracted from the battery until the voltage drops under the nominal voltage. Dependencies: To enable this parameter, in the Parameters settings, set Use a preset battery to no.

Exponential zone

[Voltage (V),
Capacity (Ah)]

Voltage, Vexp, and the capacity, Qexp, that correspond to the end of the exponential zone. The voltage should be between Vnom and Vfull. The capacity should be between 0 and Qnom. Dependencies: To enable this parameter, in the Parameters settings, set Use a preset battery to no.

Capacitance

F

The shunt capacitance, in farads (F). Default is 0.0120.

Set the initial capacitor voltage

If selected, the initial capacitor voltage is defined by the Capacitor initial voltage parameter. If cleared, the software calculates the initial capacitor voltage in order to start the simulation in steady-state. Default is selected.

Capacitor initial voltage

V

The initial capacitor voltage used at the start of the simulation. The Capacitor initial voltage parameter is not visible and has no effect on the block if the Set the initial capacitor voltage parameter is not selected.

Resistance

Ohms

The shunt branch resistance, in ohms (Ω). Default is 1e12.

Model type

Average model (Uref-controlled) is the only type of converter model.

Diode on-state resistance

Ohms

Internal resistance of the diodes, in ohms. The default value is 1e-3.

Diode snubber resistance

Ohms

The snubber resistance, in ohms. Set the snubber resistance to inf to eliminate the snubbers. The default value is 1000.

Diode snubber capacitance

F

The snubber capacitance in farads. Set the snubber capacitance to 0 to eliminate the snubbers. The default value is 1e-6.

Diode forward voltage

V

Forward voltage, in volts, across the diode when it is conducting. The default value is 1e-3.

Current source snubber resistance

Ohms

The snubber resistance across the two current sources, in ohms. Set the snubber resistance to inf to eliminate the snubbers. The default value is inf.

Rated voltage

V

The rated voltage of the BESS (Battery Energy Storage System).