Page Contents

Software Toolboxes Installed with

Improved

• Improved the license management to ensure the compatibility with OPAL-RTLinux versions 3.8 and higher.

• Reduced the time required to open projects.

• Added target information (name and ip) to the compilation log.

Fixed

• Fixed an issue where GetControlSignalDescription API fails when .signal file contains more that 24K ControlSignals.

• Fixed the issue where the model compilation could get stuck in the last steps.

• Fixed CreatePackage API to allow conversion of subfolder paths to linux.

• Fixed an issue with IEC61850 I/O interface that prevented configurations from updating properly in Dashboard.

• Fixed the possibility to cancel a load when started.

• Allowed the compilation of a project while another simulation launched by the same user is already running on the target.

Signal Visualization and Processing

Dashboards

I/O Interfaces

CAN

• Fixed issue occurring when multiple receivers are configured with the same CAN ID

General maintenance

• Removed I/O blocks that are no longer available on 64-bit operating system

  • ARINC429 MaxTechnologies

  • Applicom

  • NI-4461

  • Spectracom

  • Triphase

IEC61850

• Fixed issue with GOOSE subscriber when a data point is mapped to a floating point and its data type is a double point status

MODBUS slave

• Added option to simulate a failure of the TCP connection with the master

• Added option to add a configurable delay before responding to read/write requests from the master

OPAL-RT Board

• Added support for OP48H30 I/O card on Versal, including example models

• Added support for OP4605XG2, OP4610XG2 and OP5707XG2 platforms

• Improved model initialization time when using an I/O expansion box over MuSE

• Fixed issue with loadin ports on 64-bit operating system

S-Function IOs

• Improved model diagnostic for OP4810 and OP4815 I/O expansion boxes

Synchronization

• Fixed issue with VLAN ID that was limited to 255 instead of 4095

TCP-UDP

• Improved robustness of the reception when the transmitter send packet over multiple segments

ARTEMiS - CPU-Based Electrical Toolbox

• Added support to RT-LAB 2025.4.

• Added load-flow initialization option to the BESS block from MicroGridTestbedLibrary.

• Improved compatibility of Artemis with ePHASORSIM.

• Updated “GHOST Microgrid” example model.

• Changed output of block Islanding Management from MicroGridTestbedLibrary, the PCC_V_data was separated into V_compare and V_val and the PCC_I_data was separated into I_compare and I_val.

• Changed the example model “Microgrid_OP1420_Demo” to use the new “Islanding Management” and BESS blocks.

ePHASORSIM - CPU-Based Phasor-Domain Toolbox

• Added Native Controllable Current Source

  • This component is currently only available through PowerFactory to ePHASORSIM import

  • This will supports the current source configuration of the Static Generator

• Added support for Voltage Sources at PV busses

  • This will allow for multiple Voltage Sources in a transmission network

• Added support for all the “Model” options of static generator for PowerFactory to ePHASORSIM import

  • Only constv and constq options are suported for the local controller of static generator

• Added Pout and Qout pins that gives access to output power of the following components

  • Positive Sequence Voltage Source

  • Controllable Current Source

  • Constant Impedance Load

  • Constant Current Load

  • Constant Power Load

• Added load power report to the load flow results

  • This is available when the load flow results are exported

FPGA-Based Power Electronics Toolbox

eHS Blockset

New Features

• Added support for Round rotor Synchronous Machine (RRSM) in Schematic Editor workflow

• Added support for Salient pole Synchronous Machine (SPSM)

• Added support XG2 platform in 3 official Versal bitstreams

• Added AOMR v3 Gain/offset on the fly change to all official bitstreams.

• Added FPGA Scope support for Machines to all OP481X official bitstreams.

• Added LED support to all OP4610 official bitstreams.

• Added better error handling for Schematic Editor components compatibility.

• Added support of High density OP48H30 cards for OP481X chassis with 2 new official bitstreams.

• Added migration guide from eHS Gen4 Nodal Analysis to eHS Gen5 State space analysis.

• Added support of OP4300 chassis in eFPGASIM XSG Lib.

• Added new API to pilot the eHS simulink block from command line.

Bug fixes

• Fixed Reset Handling by AOMRv2 and AOMRv3

• Fixed "Number of resolver pole pairs" parameter for the SCIM and DFIM machines

• Fixed underestimated minimum time step of specific topologies in eHS Gen5

• Fixed Pi Line section error handling

• Fixed a voltage instability issue in the Dual Active Bridge example model.

• Fixed serializer block for DataOut.

• Fixed driver features configuration in multiple firmwares.

RT-XSG Blockset

• Retrocompatible support for new XG2 motherboard for Versal Family

• Fixed wrong ID for the expansion slot when empty

• Fixed issue causing a overtemperature for the DIO of the OP48H30 when a hardware mismatch is present

• Hidden reserved MGT blocks from the library browser