...
| Controller Name | This parameter enables the binding between this OpCtrl block and functionality blocks that must be associated with the same card. This string must be unique among all OpCtrl blocks present in the same model. |
| Board ID | This parameter is the integer value represented by the board index DIP switch of the backplane adapter board to which the card is connected. The value is in the range of 0 to 31. If the card is not connected to an adapter board, the value is 0. |
| Primary Bitstream FileName | This is the name of the primary bitstream to be programmed on the board before the model is loaded. The bitstream must have been produced with RT-XSG and must be available in the model directory at load time. Please note that the name of Bitstream file name should match the board type that is selected in the "Board Type" parameter. |
| Bitstream Configuration | This is the configuration of the bitstream to be programmed on the card before the model is loaded. This parameter allows the user to use the same bitstream for several purposes. |
| Synchronization mode | This popup allows the selection of the Master, Slave or Master with external clock mode of hardware synchronization. Master mode must be used when the card is selected as the synchronization source of the model. Slave mode can be used when the synchronization source of the model is another Opal-RT card such as OP7160, OP5110, OP5130-XSG, etc. Master with external clock mode must be used when the OpCtrl block acts as the synchronization source but receives the RTSI signal from another device. |
| Generate External Clock | Not yet supported. |
| Decimation factor | This parameter is available only when the Slave mode of synchronization is selected. Not yet supported. |
| Sample Time (s) | This parameter allows the user to specify the sample time for this block, in seconds. The default value is 0, which specifies a continuous sample time (note that the sample time is borrowed from the separated subsystem). These synchronization rules must be respected in the model:
|
| Board Type | This popup allows the selection of the board type to control. This can make the board switching process easier for the user. |
| If the Board Type selected is OP48xx, this parameter specifies: | |
| This parameter is the IP address of the Versal OP4810 or OP4815 chassis, as shown on its LCD. |
| This parameter is the name of the chassis, as and will be shown on its LCD. |
| Secondary used for Simulation | Specifies if other FPGA cards are used. A maximum of 8 cards per block are supported and for each card, one bitstream file is needed. This option is only available for OP7160 and OP7161 Board Types. |
| If the "Secondary used for Simulation" option is checked, this parameter specifies: | |
|---|---|
| The name of the first bitstream. Please note that the name of a Bitstream file name should match the board type and the slot number. |
| The name of the third bitstream. Please note that the name of a Bitstream file name should match the board type and the slot number. |
| The name of the fifth bitstream. Please note that the name of a Bitstream file name should match the board type and the slot number. |
| The name of the seventh bitstream. Please note that the name of a Bitstream file name should match the board type and the slot number. |
| The name of the ninth bitstream. Please note that the name of a Bitstream file name should match the board type and the slot number. |
| The name of the eleventh bitstream. Please note that the name of a Bitstream file name should match the board type and the slot number. |
| The name of the thirteenth bitstream. Please note that the name of a Bitstream file name should match the board type and the slot number. |
| Synchronization type | Specifies if the synchronization is done via LVDS (audio) or optical fiber. This option is only available for the VC707 card. |
| Disable strict hardware mismatch validation | This parameter activates the use of multiple I/O card types based on general compatibility rules instead of using the exact hardware ID values. This option is only available when TE0741 or VC707 is selected as board type. |
...