GENERAL | |
|---|---|
| Product Name | 32 Channels High-Range DIO |
Part numbers | OP5369 |
Board type | Digital input/output conditioning |
Form factor | Mezzanine Type B |
Dimensions | 6.60 cm x 12.50 cm (2.6” x 4.92”) |
Hot-Plug support | No |
Characteristic | |
Number of channels | 32 IO in 4 Banks configurable as inputs or outputs Bank1 : D0-7 Bank2 : D8-15 Bank3 : D16-23 Bank4 : D24-31 VUser1 for Bank 1 and 2 VUser2 for Bank 3 and 4 |
INPUT DIRECTION | |
| Input impedance | > 100 kOhm |
| Reverse voltage protection | Diode |
| Maximum voltage protection | +/- 50 Volts |
| Detection threshold | 4 programmable Schmitt trigger level step 0.118V from 0.470V to 29.4V threshold high and threshold low for each bank |
Recommended levels threshold | The default thresholds are LOW = 1.5V, HIGH = 3.5V. To improve noise immunity, a LOW level threshold of 1/3 VUser and a HIGH level threshold of 2/3 VUser are recommended. |
| Voltage range | 0 to 30 Vdc |
| Delay Low-to-High | 10 ns (implementation-dependent) |
| Delay High-to-Low | 15 ns (implementation-dependent) |
OUTPUT DIRECTION | |
Output protection | 50 mA resettable fuse |
| Output impedance | 2 to 15 Ohm |
Protection thresholds | Maximum VUser + 0.5V Minimum -0.5V |
Output voltage range | 4.5 to 25Vdc Max (default internal 4.5 volts) |
Logic high levels (typical) | No load: VUser -0.2V 50mA : VUser -0.9V (in OP5XXX system) |
| Logic low levels (typical) | No load: 0.1V 50 mA: 0.9V (in OP5XXX system) |
Output configuration | Push-pull |
Delay Low-to-High (typical value, implementation-dependent) | < 100ns @25°C for 25V < 90ns @25°C for 5 V |
Delay High-to-Low (typical value, implementation-dependent) | < 100ns @25°C for 25V < 90ns @25°C for 5 V |
Rise / Fall time | < 40ns, < 50ns |
Minimum pulse detection (resolution) | 90 ns 5V 130 ns 30V |
Output frequency | DC to 4MHz (see table below) |
Environmental | |
The OP5369 is designed for indoor use only. | |
Module operating temperature | 0 °C to 40 °C |
Storage temperature | -40 °C to 85 °C |
Operating humidity | 10% to 90% non-condensing |
Storage humidity | 5% to 95% non-condensing |
Pollution degree | 2 |
Maximum altitude | 2,000 m |
| Power requirement | 15W |
Maximum PWM Output Frequency for Given Number of Repetitive Signals
| OP5650/OP5x07/OP5705/OP4610 | OP4510 | |||||
|---|---|---|---|---|---|---|
| Vuser / Channel | <=25V | <=12V | <=5V | <=25V | <=12V | <=5V |
| 1 | 1 MHz | 2 MHz | 4 MHz | 16 kHz ** | 2 MHz | 4 MHz |
| 5 | 1 MHz | 2 MHz | 4 MHz | 16 kHz ** | 1 MHz | 4 MHz |
| 15 | 0.3 MHz ** | 2 MHz | 4 MHz | 16 kHz ** | 0.5 MHz | 2 MHz |
| 32 | 0.3 MHz ** | 1 MHz | 4 MHz | 16 kHz ** | 0.5 MHz | 1 MHz |
| ** | 0.5 MHz if T amb <= 25°C | |||||