Documentation Home Page Hardware Home Page
Pour la documentation en FRANÇAIS, utilisez l'outil de traduction de votre navigateur Chrome, Edge ou Safari. Voir un exemple.

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Next »

Board Architecture

The input/output conditioning is managed by the Type B /wiki/spaces/OP5367/pages/29360437module.

A CPLD is used to configure the fault insertion unit (FIU) section and the OP5367.  It is responsible for the communication of the SLSC card within the NI environment for identification, error reporting, etc. It also receives configuration from the software and applies it to the FIU and to some of the I/Os.

The FIU specification and topology are common to all OP8900 boards.

General

Product Name

32 Channels High Range DIO

Part Numbers

see OP8926 configurations options

Board Type

Digital input/output conditioning

Form Factor

SLSC

SLSC Module Design Specifications

Version 1.2.1

SLSC Compliance Level

1

Rear I/O Compatibility

[01] (Digital Input/Output up to 32 channels)

Hot-Plug support

no

Characteristic

Number of Channels

32 IO in 4 Banks configurable as inputs or outputs    Bank1 : D0-7    Bank2 : D8-15   Bank3 D16-23     Bank4 D24-31

Input direction

Input Impedance

> 100 K Ohm

Reverse voltage protection

Signal diode

Maximum  voltage protection

+/- 50 V

Detection threshold

4 programmable Schmitt Trigger  Level step  .1176V   from .470v to 29.4 Threshold high and  Threshold Low for each bank

Recommended levels threshold

The default thresholds are:   

LOW level = 1.5V

HIGH Level = 3.5V 

To improve noise immunity, a LOW-level Threshold of 1/3 Vuser, and a HIGH-level Threshold of 2/3 Vuser, are recommended.

Voltage Range

0 to 30 Vdc

Delay Low-to-High

10ns (implementation-dependent)                                                              

Delay High-to-Low

15ns (implementation-dependent)                                                         

Output Direction

Output Protection

50 mA resettable fuse

Output impedance

2 to 15 ohm

Protection thresholds

Maximum Vuser + 0.5V

Minimum  -0.5V

Output voltage range

4.5 to 24V Max ( default internal 4.5V)

Logic high levels ( typical) 

Vuser <= 25v , noload  :  Vuser -0.2V       50mA  : Vuser -0.8V       

Vuser  >  25v , noload  :  Vuser -3.5V       50mA  : Vuser -4.7V 

Logic Low levels ( typical) 

Vuser  5V to 30V     V low= 0.1V

Delay Low-to-high (  hardware typical * )

< 100ns @25c for  25V

< 90ns @25c for 5V                                       

Delay High-to-Low (  hardware typical * )

< 100ns @25c for  25V

< 90ns @5c for 5V                                       

Rise / Fall time ( x to Y)

< 20 ns @ 5V 

< 50ns @ 30V                                                   

Minimum Pulse detection (resolution)

90 ns   @   5V

130ns  30V

 Output Frequency

 DC to 8 Mbit (1)

Environmental

Important

Designed for indoor use only.

Storage temperature

-40 °C to 85 °C

Operating humidity

10% to 90% non-condensing

Storage humidity

5% to 95% non-condensing

Pollution Degree

2

Maximum altitude

2,000 m

Power requirement

21W

 Number of clock outputs simulated  (power limitation)

Frequency/Vuser

5V

10V

15V

22V

30V

< 500 Kb

32

32

32

32

32

1 Mb

32

32

32

24

18

2 Mb

32

32

24

14

12

4 Mb

32

24

16

8

5

8 Mb

24

16

12

5

4

 

  • No labels