Documentation Home Page ◇ eHS Toolbox Home Page
Pour la documentation en FRANÇAIS, utilisez l'outil de traduction de votre navigateur Chrome, Edge ou Safari. Voir un exemple.
eHS Requirements
Software Requirements
Recommended configurations for basic use (only circuit simulation)
- Supported MATLAB versions (32bits or 64bits): 2011b – 2012b – 2013a – 2013b – 2014b – 2015aSP1 – 2015b - 2016a – 2016b – 2017a
- RT-LAB v11.2.2 or later5
- RT-EVENTS v4.2.2 or later6
- At least one of these tools:
Simscape Electrical Specialized Power Systems (SPS) Simulink library
- Powersim PSIM v9.3.4 or v10.0.6 (v10.0.5 is unsupported)
- Plexim PLECS Simulink Library v3.7.4 or later
- NI Multisim 13
The RT-XSG toolbox requires the following software to generate programming files for reconfigurable devices and to program the platform:
Supported configuration for firmware generation
For Xilinx Zynq and 7 series
- MATLAB 2014b, 64-bit version
- Xilinx Vivado suite 2015.3 & Xilinx Vivado System Generator for DSP 2015.3
- RT-XSG v3.1.8
For Xilinx Virtex 6 series
- MATLAB 2011b, 64-bit version
- Xilinx ISE suite v14.7 (System or DSP edition) & Xilinx System Generator for DSP v14.7
- RT-XSG v2.3.5
Complete compatibility charts
MatLab
Matlab R2011b | Matlab R2012b | Matlab R2013a | Matlab R2013b | Matlab R2013b | Matlab R2015a SP1 | Matlab R2016a | Matlab R2016b | Matlab R2017a | Matlab R2017b | Matlab R2018a | Matlab R2018b | |
---|---|---|---|---|---|---|---|---|---|---|---|---|
Basic | x | x | x | x | x | x | x | x | x | x | x | x |
Firmware Generation (VC707) | N/A | N/A | N/A | N/A | x | x | x | x | x | x | x | x |
Firmware Generation (ML605) | x | N/A | N/A | N/A | N/A | N/A | N/A | N/A | N/A | N/A | N/A | N/A |
Firmware Generation (OP7XXX) | x | N/A | N/A | N/A | N/A | N/A | N/A | N/A | N/A | N/A | N/A | N/A |
Firmware Generation (OP4510) | N/A | N/A | N/A | N/A | x | x | x | x | x | x | x | x |
Firmware Generation (OP4200) | N/A | N/A | N/A | N/A | x | x | x | x | x | x | x | x |
N/A – Unsupported, X – Supported, Beta – Available but not verified
- 5 The eHSx32 for OP4200 block is currently only supported from RT-LAB v11.1.1.
- 6 RT-EVENTS is unsupported on the OP4200 target.
RT-LAB vs Hardware chassis (only circuit simulation)
Chassis | RT-LAB v10.4 | RT-LAB v10.5 | RT-LAB v10.6 | RT-LAB v10.7 | RT-LAB v11.0 | RT-LAB v11.1 | RT-LAB v11.2 | RT-LAB v11.3 |
---|---|---|---|---|---|---|---|---|
OP5600 chassis (ML605 board) | N/A | x | x | x | x | x | x | x |
OP7000 chassis (OP7161 board) | N/A | x | x | x | x | x | x | x |
OP7020 chassis (VC707 board) | N/A | N/A | x | x | x | x | x | x |
OP5607 chassis (VC707 board) | N/A | N/A | N/A | x | x | x | x | x |
OP4500 chassis (MMPK7 board) | N/A | N/A | x | x | x | x | x | x |
OP4510 chassis (TE0741 board) | N/A | N/A | N/A | x | x | x | x | x |
OP4200 chassis (MEZX5 board) | N/A | N/A | N/A | N/A | N/A | x | x | x |
N/A – Unsupported, X – Supported
RT-XSG vs Hardware chassis (for firmware generation only)
Chassis | RT-XSG v2.3.5 | RT-XSG v3.0.X | RT-XSG 3.1.X | RT-XSG 3.2.X |
---|---|---|---|---|
OP5600 chassis (ML605 board) | x | N/A | N/A | N/A |
OP7000 chassis (OP7161 board) | x | N/A | N/A | N/A |
OP7020 chassis (VC707 board) | x | x | x | x |
OP5607 chassis (VC707 board) | x | x | x | x |
OP4500 chassis (MMPK7 board) | x | Beta | Beta | Beta |
OP4510 chassis (TE0741 board) | x | x | x | x |
N/A – Unsupported, X – Supported, Beta – Available but not verified
Installation Notes
After installing MATLAB, RT-LAB and RT-EVENTS (plus Xilinx ISE and RT-XSG for firmware generation), install eFPGAsim using the install shield provided. When the installation is done, open a MATLAB instance and type ver. The eFPGAsim blockset is correctly installed when it appears in the toolbox list of MATLAB.
OPAL-RT TECHNOLOGIES, Inc. | 1751, rue Richardson, bureau 1060 | Montréal, Québec Canada H3K 1G6 | opal-rt.com | +1 514-935-2323
Follow OPAL-RT: LinkedIn | Facebook | YouTube | X/Twitter