HIL2GO-100 - I/O Group 1, Section A (CH 00-31) - Digital Inputs or Outputs (OP5369)

Connected I/O module is OP5369 32-Channel Digital IO Board

Before designing cables, OPAL-RT recommends using the guideline Simulator EMC cable recommendations.
Before connecting the cables, make sure that the voltages or other electrical specifications are compatible with OPAL-RT DB37 specifications of I/O module OP5369.

Connector P1 Group 1 - Section A - Channel 00 to 15				Connector P2 Group 1 - Section A - Channel 16 to 31
DB37F Pin	Assignment	DB37F Pin	Assignment	DB37F Pin	Assignment	DB37F Pin	Assignment
1	+D00	20	GND	1	+D16	20	GND
2	+D01	21	GND	2	+D17	21	GND
3	+D02	22	GND	3	+D18	22	GND
4	+D03	23	GND	4	+D19	23	GND
5	+D04	24	GND	5	+D20	24	GND
6	+D05	25	GND	6	+D21	25	GND
7	+D06	26	GND	7	+D22	26	GND
8	+D07	27	GND	8	+D23	27	GND
9	+D08	28	GND	9	+D24	28	GND
10	+D09	29	GND	10	+D25	29	GND
11	+D10	30	GND	11	+D26	30	GND
12	+D11	31	GND	12	+D27	31	GND
13	+D12	32	GND	13	+D28	32	GND
14	+D13	33	GND	14	+D29	33	GND
15	+D14	34	GND	15	+D30	34	GND
16	+D15	35	GND	16	+D31	35	GND
17	+12 V*	36	GND	17	+12 V*	36	GND
18	Vuser 1	37	Vrtn 1	18	Vuser 2	37	Vrtn
19	Not used			19	Not used

* Internally provided by the simulator. Non-isolated, limited to 400 mA.

If used as digital output, channels will require a Vuser reference of 4.5 to 24 Vdc max (default internal 4.5 volts), which is provided through the DB37 connector pin 18 and referenced to Vrtn pin 37.

The OP5369 32-channel digital IO board can be configured per 8-channel subsection to be used as digital inputs or digital outputs. The following table is a list of parameters to configure as input or output.

I/O MODULE OPTION BLOCK
Parameters	CH00-07 / CH08-15 / CH16-23 / CH24-31
Controller Name	'OP4512 OpCtrl'
Mezzanine-type I/O module	OP5369 - 32 DIO
Direction	Input	Output
Threshold low (volt)	0.470 to 29.4 V	N/A
Threshold high (volt)	0.470 to 29.4	N/A

DIGITAL OUTPUT BLOCK PARAMETERS
Parameters	CH00-07	CH08-15	CH16-23	CH24-31
Controller Name	'OP4512 OpCtrl'
Data In Port Number	11	12	13	14
Number of channels	8	8	8	8
Digital Output Type	Static Digital Out Event Generator Pulse-Width Modulated Output	Static Digital Out Event Generator Pulse-Width Modulated Output	Static Digital Out Event Generator Pulse-Width Modulated Output	Static Digital Out Event Generator Pulse-Width Modulated Output

DIGITAL INPUT BLOCK PARAMETERS
Parameters	CH00-07	CH08-15	CH16-23	CH24-31
Controller Name	'OP4512 OpCtrl'
Data Out Port Number	3	4	5	6
Number of channels	8	8	8	8
Digital Input Type	Static Digital In Event Detector Pulse-Width Modulated Input	Static Digital In Event Detector Pulse-Width Modulated Input	Static Digital In Event Detector Pulse-Width Modulated Input	Static Digital In Event Detector Pulse-Width Modulated Input