In the lower section of the unit, the OP4610XG 2nd Edition has one large round button with an integrated LED indicator (D), while the 1st Edition has two small buttons and two working LED indicators (D).

Open

OP4610XG 2nd Edition with one large round button and an integrated DEL indicator (D)

Open

OP4610XG 1st Edition with two small buttons and two working LED indicators (D)

Upper section

A. Small form-factor pluggable (SFP) module connectors provide four high-speed communication links between other FPGA simulators or third-party devices. Each socket controls one communication link. SFP transceivers and fiber-optic cables must be selected (and purchased separately) according to the type and speed of the communication protocol.

• Note: MuSE link requires specific SFP transceivers and optical fiber cables:

  • SFP: Avago AFBR-57R5APZ

  • Cable: LC-LC multimode 850 nm optical fiber

B. JTAG connector (for OPAL-RT technicians’ use only).

• Note: JTAG connector is highly sensitive to Electro Static Discharge (ESD). Always leave plastic plug in place when not in use. Wear an anti-static wrist strap at all times when using this connector.

C. Synchronization connectors status and user-configurable LEDs, dip switch and synchronization connectors.

• LED Label

  • PROG/CFG OK:

    • CFG OK steady on green and PROG off indicates the FPGA is functioning normally.

    • CFG OK off and PROG steady on yellow indicate the FPGA has stopped and is no longer functioning.

  • RX: Green when receiving synchronization.

  • TX: Green when transmitting synchronization.

  • USER 1: Green LED controlled. Configured by the user using Simulink blocks.

  • USER 2: Green LED controlled. Configured by the user using Simulink blocks.

  • PWR ON: Green indicates that the power is on.

  • MASTER/SLAVE:

    • Green indicates MASTER mode.

    • Yellow indicates SLAVE mode.

    • Flashing green and yellow indicates a SAFE bitstream in the FPGA

• Dip switches

  • CHASSIS INDEX: 8-pin DIP switch that allows users to set the device’s network chassis index.

    • It can be set from 00 to FF (in HEX) or 0 to 255 (in decimal) for a maximum of 256 addresses.

    • Otherwise specified in the “System description” document delivered with your system, the default value = 00.

    • Refer to General Configuration to copy this value in RT-LAB.

    • Set the dip switches in binary code on 8-bit to change the chassis ID number. Switch down is 0 and switch up is 1
      
      

• SYNCHRO Connectors

  • TX/RX Fiber-Optic Connectors (square connectors): Compatible with OP4500, OP5607, OP7000 and OP7020. Synchronizes time steps between systems and includes high-speed FPGA pulses.

  • TX/RX Copper Cable Connectors (3.5 mm audio jack connectors): Legacy connectors compatible with all OPAL-RT products except OP4200, OP5705, OP5650.

Lower Section

OP4610XG 2nd Edition (Large Round Button)

D. Target computer monitoring interface. One push button with an integrated LED indicator:

• Power and Reset Push Button:

  • Normal press: Power On or shut down the target computer.

  • Long press: If the button is pressed for at least 4 seconds, the computer will shut down.

• Integrated LED

  • Green : Target computer is On

  • Black (unlit): Target computer is Off

OP4610XG 1st Edition (Small Buttons and LEDs)

D. Target computer monitoring interface. Two push buttons and six LED indicators:

• Power Push Button: Power on or shut down the target computer.

• Reset Push Button: Resets the target computer.

• Power Green LED: On indicates that the unit is powered up.

• HDD Green LED: On indicates that the hard disk drive is operating.

• NIC1: Not used

• NIC2: Not used

• Power Fail: Not used

• Overheat/Fan Fail: Not used