Documentation Home Page ◇ Hardware Home Page
Pour la documentation en FRANÇAIS, utilisez l'outil de traduction de votre navigateur Chrome, Edge ou Safari. Voir un exemple.

OP4610XG Rear Interface

Owned by Sylvain Ménard
Last updated: Dec 04, 2023
3 min read

Page Content

OP4610XG Standard Configuration

A. DB37 connectors for digital or analog inputs and outputs.

B. In the standard OP4610XG configuration, this section contains a DB9 connector module for RS422 signals typically used to transmit differential encoder inputs and outputs; however, other options are available.

C. Standard computer connectors (from left to right):

  • 1 VGA Port

  • 1 Serial Port (COM1)

  • 2 1G LAN RJ-45 Ports

  • 1 IPMI LAN RJ-45 Port

  • 2 USB 3.2 Gen 2 Ports

  • 1 HDMI Port

  • 2 10G LAN RJ-45 Ports

  • Unit Identifier (UID) switch

D. 2 PCIe free slots are available for optional I/O card. See OP4610XG PCIe optional I/O cards below.

OP4610XG I/O Expansion Options 

The OP4610XG comes with an RS-422 Connector Kit (OP5969-1) factory installed by default.

The optional Fiber-Optic Connector Kit (OP5969-2) can also be installed. It will replace the default connector kit, since only ONE of these connector kits can be installed in an OP4610XG at a time.

The optional connector kit must be selected at the time of purchase and factory-installed.



RS422 Connector kit
(OP5969-1)

OP4510 V2-1 RS422 Connectors
OP4510 V2-1 RS422 Connectors

DEFAULT connector kit installed
The DB9 connectors for RS422 signals are typically used to transmit differential encoder inputs and outputs. Refer to the OP5969-1 User Manual for specifications and pin assignment.

Fiber-Optic Connector kit
(OP5969-2)

Optional connector kit
Fiber-optic connector kit provides 6 RX and 6 TX channels.
These channels can be used as digital I/Os or for low-speed communication protocols.
The ORION protocol, developed by OPAL-RT is compatible with these channels and available in custom bitstreams. Refer to the OP5969-2 User Manual for specifications and pin assignment.

OP4610XG PCIe Optional I/O Cards

The following PCIe options are available for the OP4610XG:

  • Up to 2 expansion kits listed below may be installed in an OP4610XG.

NOTE: PCIe optional cards must be selected at the time of purchase and factory-installed.

OP5451
Copper cable



Passive/active PCIe expansion with standard PCIe iPass x4 connector interface. This option is used to connect the OP4610XG to an OPAL-RT expansion I/O chassis. The option comes as a kit including a 2 m (6 ft) copper cable.

Platforms

  • OP4610XG to OP4520

  • OP4610XG to OP5607

  • OP4610XG to OP5705-IO

  • OP4610XG to OP5707-IO

OP3411

CANbus protocol expansion board with a CANbus standard 25-pin connector interface.

OP3811


GPS time synchronization (IEEE 1588) with RJ45 connector interface and expansion connector plate with external synchronization input connectors and Fiber-optic synchronization output.

OP3812

GPS time synchronization (IEEE 1588) with SFP connector interface and expansion connector plate with external synchronization input connector and Fiber-optic synchronization output.

OP3821

Dual-port PCIe x1 Gigabit Ethernet interface.



OPAL-RT TECHNOLOGIES, Inc. | 1751, rue Richardson, bureau 1060 | Montréal, Québec Canada H3K 1G6 | opal-rt.com | +1 514-935-2323