Advanced | SIDYN2V

DYNAMIC RESPONSE – [SIDYN2V]
Computes the dynamic response of a control signal following a disturbance....

CATEGORY
Advanced

DESCRIPTION
The function computes the dynamic response of a control system after a disturbance. This function allows computing mean, minimum and maximum values and stabilization times.
Note: The order of operations of this function is not as important as for other functions, but it is useful to know.

1	Course of the signal from reference Ref_Time1 to reference Ref_Time2 to find the minimum and maximum of the disturbance.
2	Calculation of the mean on the Interval (moyd) first milliseconds, of the mean on the interval (moyf) last milliseconds and of the mean on the Interval (moyp) milliseconds preceding reference Ref_Time2. These values are returned as the moyd, moyf and moyp results.
3	Calculation of time taken to reach the different threshold values for the stabilization times.

RESULT VARIABLES AND PARAMETERS

maxp	Maximum value of the input signal between first and second reference times (Ref_Time1, Ref_Time2).
minp	Minimum value of the input signal between first and second reference times (Ref_Time1, Ref_Time2).
moyd	Mean value before the disturbance. The mean value is computed on the first milliseconds of the analysis, i.e. before the average time start (Avg_Time_Start).
moyf	Mean value after the disturbance. The mean value is computed on the last milliseconds of the analysis, i.e. after the average time end (Avg_Time_End).
moyp	Mean value during the disturbance. The mean value is computed between the average perturbation time (Avg_Time_Pert) and the reference time 2 (Ref_Time2).
tst0	Zeroth stabilization time. Time in milliseconds [ms] relative to the second reference time (Ref_Time2) when the 0 threshold value (Threshold0) is reached after reference time 2 (Ref_Time2).
tst1	First stabilization time. Time in milliseconds [ms] relative to the second reference time (Ref_Time2) when the first threshold value (Threshold1) is reached, minus reference time 2 (Ref_Time2).
tst2	Second stabilization time. Time in milliseconds [ms] relative to the second reference time (Ref_Time2) when the second threshold value (Threshold2) is reached, minus reference time 2 (Ref_Time2).
tst3	Third stabilization time. Time in milliseconds [ms] relative to the second reference time (Ref_Time2) when the third threshold value (Threshold3) is reached, minus reference time 2 (Ref_Time2).
Signal	input signal to analyze.
Threshold0	Threshold used to compute the zero stabilization time. This percentage [%] of the mean before disturbance is added to or subtracted from the mean to latter determine the threshold to reach in order to evaluate the response time. The percentage is subtracted if the mean before disturbance is higher than the mean during the disturbance. When the opposite is true, the mean is added.
Threshold1	Threshold used to compute the first stabilization time. This percentage [%] of the mean before disturbance is added to and then subtracted from the mean before disturbance to yield two threshold values, one on each side of the mean before disturbance. The stabilization time is computed using these two threshold values.
Threshold2	Threshold used to compute the second stabilization time. This percentage [%] of the mean before disturbance is added to and then subtracted from the mean before disturbance to yield 2 threshold values, one on each side of the mean before disturbance. The stabilization time is computed using these two threshold values.
Threshold3	Threshold used to compute the third stabilization time. This percentage [%] of the mean before disturbance is added to and then subtracted from the mean before disturbance to yield 2 threshold values, one on each side of the mean before disturbance. The stabilization time is computed using these two threshold values
Ref_Time1	Time in milliseconds [ms] serving as reference for the beginning of the disturbance. This time is relative to time 0 of the acquisition buffer.
Ref_Time2	Time in milliseconds [ms] serving as reference for the end of the disturbance. This time is relative to time 0 of the acquisition buffer.
Avg_Time_Start	Time interval in milliseconds [ms], at the beginning of the analysis limits, on which is computed the mean value before the disturbance (moyd).
Avg_Time_End	Time interval in milliseconds [ms], at the end of the analysis limits, on which is computed the mean value after the disturbance (moyf)
Avg_Time_Pert	Time interval in milliseconds [ms] ending at reference time (Ref_time2), on which is computed the mean value during the disturbance (moyp).
Begin_time	Time at which the analysis of a signal must start. This time is expressed in milliseconds [ms]. This value must be greater than 0 and lower than the size of the acquisition buffer. The default value is 0.
End_time	Time at which the analysis of a signal must end. This time is expressed in milliseconds [ms]. The value of this time must be larger than the specified begin_time and smaller than the duration of the test. Use the “HUGE” value to specify the end of the test. The default value is HUGE.
Factor	Multiplying factor for the results generated by the function. The default value of the multiplying factor is 1.0 and has no effect on the results. The multiplying factor only applies to the following results: tst0, tst1, tst2 and tst3. The other results are not modified.

SYNTAX
[maxp, minp, moyd, moyf_1, moyp, tst0, tst1, tst2, tst3] = sidyn2v(input, threshold0, threshold1, threshold2, threshold3, time1, time2, time_start, time_end, time_pert, 0, HUGE, 1)

CHARACTERISTICS
Data type support
Double Floating point

EXAMPLE
The following figure shows the results for a signal whose disturbance voltage is lower than initial voltage.

The following figure shows the results for a signal whose disturbance voltage exceeds the initial voltage.