OP8615 Pin Assignments and Specifications
Connector Diagram
Each pair of jacks connects from a channel on the unit under test to a channel on the simulator.
Front banana jacks path to connector
Faults are manually created by removing a jumper into the desired channel jacks. The jumper used for the break-out box are supplied.
In the event that replacements are needed, we recommend using the original part (SKS2-12L/1SA/N, 12mm jumper, 2mm), or an equivalent.
As a general guideline, cables from the Break-Out Box to the controller should be connected on the RED jacks and cables from the simulator to the Break-Out Box should be connected to the BLACK jacks.
Low current connector pin assignments
The following table lists the signals available on the front, low current connector and on the system’s two rear connectors.
Red (left) breakout pin | Red Rear connector | Black (right) breakout pin | Black Rear connector |
|
|---|---|---|---|---|
A1 | 1-1 | A1 | 1-1 | |
B1 | 1-2 | B1 | 1-2 | |
A2 | 1-3 | A2 | 1-3 | |
B2 | 1-4 | B2 | 1-4 | |
A3 | 1-5 | A3 | 1-5 | |
B3 | 1-6 | B3 | 1-6 | |
A4 | 1-7 | A4 | 1-7 | |
B4 | 1-8 | B4 | 1-8 | |
A5 | 2-1 | A5 | 2-1 | |
B5 | 2-2 | B5 | 2-2 | |
A6 | 2-3 | A6 | 2-3 | |
B6 | 2-4 | B6 | 2-4 | |
C1 | 2-5 | C1 | 2-5 | |
D1 | 2-6 | D1 | 2-6 | |
C2 | 2-7 | C2 | 2-7 | |
D2 | 2-8 | D2 | 2-8 | |
C3 | 3-1 | C3 | 3-1 | |
D3 | 3-2 | D3 | 3-2 | |
C4 | 3-3 | C4 | 3-3 | |
D4 | 3-4 | D4 | 3-4 | |
C5 | 3-5 | C5 | 3-5 | |
D5 | 3-6 | D5 | 3-6 | |
C6 | 3-7 | C6 | 3-7 | |
D6 | 3-8 | D6 | 3-8 | |
E1 | 4-1 | E1 | 4-1 | |
F1 | 4-2 | F1 | 4-2 | |
E2 | 4-3 | E2 | 4-3 | |
F2 | 4-4 | F2 | 4-4 | |
E3 | 4-5 | E3 | 4-5 | |
F3 | 4-6 | F3 | 4-6 | |
E4 | 4-7 | E4 | 4-7 | |
F4 | 4-8 | F4 | 4-8 | |
E5 | 5-1 | E5 | 5-1 | |
F5 | 5-2 | F5 | 5-2 | |
E6 | 5-3 | E6 | 5-3 | |
F6 | 5-4 | F6 | 5-4 | |
G1 | 5-5 | G1 | 5-5 | |
H1 | 5-6 | H1 | 5-6 | |
G2 | 5-7 | G2 | 5-7 | |
H2 | 5-8 | H2 | 5-8 | |
G3 | 6-1 | G3 | 6-1 | |
H3 | 6-2 | H3 | 6-2 | |
G4 | 6-3 | G4 | 6-3 | |
H4 | 6-4 | H4 | 6-4 | |
G5 | 6-5 | G5 | 6-5 | |
H5 | 6-6 | H5 | 6-6 | |
G6 | 6-7 | G6 | 6-7 | |
H6 | 6-8 | H6 | 6-8 | |
J1 | 7-1 | J1 | 7-1 | |
K1 | 7-2 | K1 | 7-2 | |
J2 | 7-3 | J2 | 7-3 |
Red (left) breakout pin | Red Rear connector | Black (right) breakout pin | Black Rear connector |
|---|---|---|---|
K2 | 7-4 | K2 | 7-4 |
J3 | 7-5 | J3 | 7-5 |
K3 | 7-6 | K3 | 7-6 |
J4 | 7-7 | J4 | 7-7 |
K4 | 7-8 | K4 | 7-8 |
J5 | 8-1 | J5 | 8-1 |
K5 | 8-2 | K5 | 8-2 |
J6 | 8-3 | J6 | 8-3 |
K6 | 8-4 | K6 | 8-4 |
L1 | 8-5 | L1 | 8-5 |
M1 | 8-6 | M1 | 8-6 |
L2 | 8-7 | L2 | 8-7 |
M2 | 8-8 | M2 | 8-8 |
L3 | 9-1 | L3 | 9-1 |
M3 | 9-2 | M3 | 9-2 |
L4 | 9-3 | L4 | 9-3 |
M4 | 9-4 | M4 | 9-4 |
L5 | 9-5 | L5 | 9-5 |
M5 | 9-6 | M5 | 9-6 |
L6 | 9-7 | L6 | 9-7 |
M6 | 9-8 | M6 | 9-8 |
N1 | 10-1 | N1 | 10-1 |
P1 | 10-2 | P1 | 10-2 |
N2 | 10-3 | N2 | 10-3 |
P2 | 10-4 | P2 | 10-4 |
N3 | 10-5 | N3 | 10-5 |
P3 | 10-6 | P3 | 10-6 |
N4 | 10-7 | N4 | 10-7 |
P4 | 10-8 | P4 | 10-8 |
N5 | 11-1 | N5 | 11-1 |
P5 | 11-2 | P5 | 11-2 |
N6 | 11-3 | N6 | 11-3 |
P6 | 11-4 | P6 | 11-4 |
R1 | 11-5 | R1 | 11-5 |
S1 | 11-6 | S1 | 11-6 |
R2 | 11-7 | R2 | 11-7 |
S2 | 11-8 | S2 | 11-8 |
R3 | 12-1 | R3 | 12-1 |
S3 | 12-2 | S3 | 12-2 |
R4 | 12-3 | R4 | 12-3 |
S4 | 12-4 | S4 | 12-4 |
R5 | 12-5 | R5 | 12-5 |
S5 | 12-6 | S5 | 12-6 |
R6 | 12-7 | R6 | 12-7 |
S6 | 12-8 | S6 | 12-8 |
T1 | 13-1 | T1 | 13-1 |
U1 | 13-2 | U1 | 13-2 |
T2 | 13-3 | T2 | 13-3 |
U2 | 13-4 | U2 | 13-4 |
T3 | 13-5 | T3 | 13-5 |
U3 | 13-6 | U3 | 13-6 |
T4 | 13-7 | T4 | 13-7 |
U4 | 13-8 | U4 | 13-8 |
T5 | 14-1 | T5 | 14-1 |
U5 | 14-2 | U5 | 14-2 |
T6 | 14-3 | T6 | 14-3 |
Red (left) breakout pin | Red Rear connector | Black (right) breakout pin | Black Rear connector |
|---|---|---|---|
U6 | 14-4 | U6 | 14-4 |
V1 | 14-5 | V1 | 14-5 |
W1 | 14-6 | W1 | 14-6 |
V2 | 14-7 | V2 | 14-7 |
W2 | 14-8 | W2 | 14-8 |
V3 | 15-1 | V3 | 15-1 |
W3 | 15-2 | W3 | 15-2 |
V4 | 15-3 | V4 | 15-3 |
W4 | 15-4 | W4 | 15-4 |
V5 | 15-5 | V5 | 15-5 |
W5 | 15-6 | W5 | 15-6 |
V6 | 15-7 | V6 | 15-7 |
W6 | 15-8 | W6 | 15-8 |
X1 | 16-1 | X1 | 16-1 |
Y1 | 16-2 | Y1 | 16-2 |
X2 | 16-3 | X2 | 16-3 |
Y2 | 16-4 | Y2 | 16-4 |
X3 | 16-5 | X3 | 16-5 |
Y3 | 16-6 | Y3 | 16-6 |
X4 | 16-7 | X4 | 16-7 |
Y4 | 16-8 | Y4 | 16-8 |
Connector Requirements
Connectors require specific male connectors. The part numbers provided are for reference purposes only and may differ according to supplier and country.
Part | Part Number | Description |
|---|---|---|
Connector | 110535-000 | ITT Cannon DL1-156 ,RECTANGULAR, PLUG, 156POS, PANEL |
PIN | 030-2409-003 | ITT Cannon CONTACT, PIN, 22-20AWG, CRIMP |
Backshell | DL1-J/S | ITT Cannon JUNCTION SHELL KIT, DL1, CONNECTOR |
handle | 204-0016-000 | ITT Cannon ACTUATING HANDLE KIT, DL CONNECTOR |
Key way | 320-0021-005 | POLARIZING POST KIT - Center Mounting for DL1/2, DLM1/2 |
Specifications
Product name | Break-Out Box |
|---|---|
Part number | OP8615 |
Number of channels | Low current: 128 channels, 5A |
Voltage range | 0-30 Vdc |
Form factor | 3 U |
Dimensions | 13.33 x 48.26 x 30.8cm HxWxD (5.25” x 19” x 12.125”) |
I/O connector | Low current: ITT Cannon DL1-156, SEB2-R 2 mm banana jack with 12 mm jumper |
Operating temperature | 10 to 40 ºC (50 to 104ºF) |
Storage temperature | -55 to 85ºC (-67 to 185ºF) |
Relative humidity | 10 to 90%, non-condensing |
Maximum altitude | 2,000 m (6562 ft.) |
OPAL-RT TECHNOLOGIES, Inc. | 1751, rue Richardson, bureau 1060 | Montréal, Québec Canada H3K 1G6 | opal-rt.com | +1 514-935-2323