Documentation Home Page Hardware Home Page
Pour la documentation en FRANÇAIS, utilisez l'outil de traduction de votre navigateur Chrome, Edge ou Safari. Voir un exemple.

OP5705-IO System Description


The OP5705-IO expansion unit was designed with the Xilinx® Artix®-7 200T FPGA to provide additional inputs and outputs to OPAL-RT simulators.
The FPGA is used to execute models designed with OPAL-RT RT-XSG, manage I/O lines and execute embedded FPGA-based simulations.
It can be connected to OPAL-RT simulators via MUlti-System Expansion link (MuSE) or PCIe link.

The combination of this versatile FPGA, with a high number of I/O lines (up to 256), and high-speed connectivity for communication with the OPAL-RT simulator and with third-party units under test (UUT), makes the OP5705-IO perfectly suited to I/O intensive simulations.

Features 

  • Xilinx® Artix®-7 200T FPGA technology:
    • Programmed via MuSE or PCIe link.
    • The FPGA is used to execute models designed with the OPAL-RT RT-XSG tool, manage the I/O lines and execute embedded FPGA-based simulations.
    • It exchanges data with the real-time simulations running on the target computer CPUs via MuSE.
  • Capable of controlling any combination of up to eight OP5300 Mezzanine Modules (analog or digital)
    • Each module controls 16 or 32 lines for a total of up to 256 I/O.
  • 4 SFP ports for high-speed communication between FPGA-based systems or external devices

System Architecture

The figure below shows a block diagram showing the architecture of the OP5705-IO Expansion Unit linked to a simulator acting as the primary device.
By default, the communication link is using MuSE via one SFP socket (illustrated in the block diagram below). Other free SFP sockets can be used to connect other devices.
Optional communication links are available (see next section).

Communication with the Master Unit

The OP5705-IO can communicate with the simulator (or master unit) in three different ways:

  • Using SFP socket (default communication mean), see the section above.
  • Using optional Dolphin SW-Link PCIe adapter
  • Using optional OneStop PCIe Target Cable Adapter

The figure below shows a block diagram showing the architecture of the OP5705-IO Expansion Unit linked to a simulator acting as the primary device using Dolphin or OneStop PCIe adapter.
To communicate, both the simulator and the I/O expansion unit must have the same PCIe adapter card.



Important note

Optional Dolphin SW-Link PCIe adapter and OneStop PCIe Target Cable Adapter must be ordered at the purchase of the unit.
Each card must be factory installed in a PCIe slot at the back of the chassis.
Cables are sold separately.

SFP Interconnection

The four SFP sockets allow interconnection with other OPAL-RT chassis or external devices, like amplifiers or MMC controllers.
The standard communication protocols available with the OP5705-IO are based on Xilinx Aurora (1 to 5 Gbps). 

There are two standard modes of operation available for the SFP ports, both based on the Xilinx Aurora communication protocol:

  • Generic Aurora communication: this mode is enabled using the Generic Aurora blocks of the OPAL-RT RT-XSG toolbox.
    • These blocks are used to exchange data with third-party devices or with other OPAL-RT systems.
    • The data communication layer (data packing/unpacking) must be configured by the user according to the targeted application.
    • The communication speed is configurable between 1 and 5 Gbps and the SFP transceivers must be selected accordingly.
  • OPAL-RT MUlti-System Expansion link (MuSE): this mode encapsulates the Aurora protocol within a network protocol designed by OPAL-RT for inter-system communication.
    • The communication speed is set to 5Gbps by default, but downgrades automatically to the speed of the other port, if that port is used at a lower speed for third-party device connection.
    • Only one SFP is used for the MuSE link, the other SFP ports remain available for the legacy Generic Aurora link.

Other protocols like the Gigabit Ethernet can also be implemented.

Note

The MuSE link is compatible with OPAL-RT Boards and OPAL-RT’s new I/O management software architecture.
Restrictions to using MuSE with OPAL-RT Board software architecture may apply depending on your application and software configuration.
Contact your sales representative or field application engineer to verify compatibility.

OPAL-RT TECHNOLOGIES, Inc. | 1751, rue Richardson, bureau 1060 | Montréal, Québec Canada H3K 1G6 | opal-rt.com | +1 514-935-2323