User Notifications from FPGA Power Electronic Toolbox

Error (100): A firmware should be selected from the circuit editor simulator setup.

Error (101): Number of scenarios used on FPGA (6) exceeds the maximum supported for this circuit (5). To support more scenarios use option "use CPU to store and load scenario"

Error (102): The model is empty. Please provide some inputs.

Error (103): Circuit should contain at least one measurement to be usable.

Error (104): The model shall not be composed of two disjoint circuits when analysis method is Nodal Analysis (eHS Gen4). Circuits composed of multiple separated sub-circuits are not supported in this case.

Error (105): The number of sources exceeds the limit supported by eHS Gen4 x16. The maximum number of sources allowed in the circuit is 16.

Error (106): The number of switches (93) exceeds the limit (48) supported by eHS Gen 5 x32. Switches are added by:

- Single Switch: 47 units * 1 switches

- Half Bridge: 23 units * 2 switches

Error (107): The number of measurements exceeds the limit supported by eHS Gen4 x16. The maximum number of measurements allowed in the circuit is 16.

Error (108): The number of states exceeds the limit supported by eHS Gen4 x16. The maximum number of electrical states allowed in the circuit is 80.

Error (109): The maximum number of PMSM DQ supported is exceeded in the schema. For the selected firmware, only a maximum of 2 PMSM DQ is allowed.

Error (110): Unsupported resource file extension: jpeg. Variable DQ only supports JMAG (.rtt) and ANSYS (.txt) formats.

Error (111): The machine 'scim1' has its parameter Excitation Type assigned to external but no Analog Input has been assigned to the parameter Excitation Source.

Error (112): The component 'pmsm1' parameter Resource File cannot be found. Please provide some input in the "Motor Configuration" field in the Schematic Editor model.

Error (113): The current version of the firmware does not support the BLDC machine.

Error (114): The model configuration requires a firmware resource of type PMSM / BLDC, but none was found in the selected firmware VC707_2-EX-0001-3_2_8_621-eHSx128_Gen4_PMSMSH_IOConfig1-03-04.

Error(115): The number of gates driven via the CPU exceeds the limit supported with the selected firmware. The maximum number of gates driven via the CPU allowed in the circuit is 72.

Error (116): Error parsing the PMSM VDQ configuration file. Please update your file, following parameters are missing: DqTransformAngleOffset.

Error(117): The time step of eHS must be positive, but '-3.26' was found.

Error(118): Unable to achieve the requested user time step of 200 ns. The minimum achievable time step for this circuit is 210 ns. (eHS cannot achieve the desired time step).

Error(119): Unable to achieve the requested user time step of 4000 ns. The minimum achievable time step for this circuit is 2500 ns. (eHS cannot achieve the desired time step).

Error(120): Circuit with a 'PMSM Spatial Harmonics' block requires a time step (Ts) multiple of 50 ns.

Error (121): The number of AC sources (40) exceeds the supported limit. For the selected firmware, only a maximum of 32 AC sources are allowed.

Error (122): The circuit exceeds the number of computation unit available. Try to reduce the number of inputs, outputs, measurements or find equivalent circuit for group of components.

Error (123): The circuit validation has failed. Errors during circuit analysis:
 - The capacitor c2 cannot be connected in parallel with voltage source vsrc2.
 - The inductor l2 cannot be connected in series with current source isrc1.

Error (124): Unsupported component sw1 (SW) with eHS Gen 5 solver.

Error (125): Model time step specified in the Schematic Editor (206ns) should be a multiple of the smallest circuit time step granularity (50ns).

Error (126): Unsupported firmware license class for eHS Gen5: x64.

Error (127): No state found in the circuit. Circuit should contain at least one state (Inductor, Capacitor, Transformer).

Error (128): The Schematic Editor version 2.8.3 in use is not compatible with eFPGASIM version 2.9.1. Please install Schematic Editor version 2.9.1 or higher.

Error (129): The selected solver settings Analysis Method Nodal Analysis(eHS Gen 4) is not compatible with the firmware VC707_2-EX-0001-3_3_1_790-eHSx128_Gen5_IOConfig1-F5-4E.

Error (131): OPAL-RT Unified Database is unavailable. Please verify your Schematic Editor installation.

Error (132): The number of non-linear components (70) exceeds the supported limit. Only a maximum of 64 are allowed.

Error (133): Surge arrester sa1 has invalid parameters (it must have k2 > k1, k2 > k3 and alpha1 > alpha2 > alpha3).

Error (134): The value v1 of the parameter p1 is invalid. The value must be (greater than or equal to | greater than | less than or equal to | less than) to v2.

Error (135): The value v1 of the parameter p1 is invalid. The value must be an integer.

Error (136): The circuit size exceeds the number of computation unit available to support multiple scenarios (529/512).

Error (137): The values for parameter IV Table voltages values are invalid. The values need to be strictly monotonically increasing. Please refer to page "Surge Arrester IV parameters file" in official documentation for further details.

Error (138): The feature Scenario from CPU is unsupported with current version 0.0.0 of eHS, needs 1.0.0 or higher. Update to a firmware which contains a newer version of the block to use this feature.

Error (139): Cannot read resource file, JSON file had following formatting issue: Unterminated array at line 1 column 23 path $.backEmfValues[1]

Error (140): Unable to process circuit with the specified parameters, singularity while trying to invert matrix. To remedy:

1. If possible, try changing discretization method to Backward Euler.

2. Try adding high value resistances between primary and secondary of transformers.

3. Try adjusting the relaxation parameter of switches and bridge components.

Error (141): The total number of switches (100) added by Half Bridges (2), Single Phase Cycloconverters (8) & 3-Lvl Arms (4) exceeds the limit supported by eHS Gen 5 x128. The maximum number of Half Bridge & Single Phase Cycloconverter switches allowed in the circuit is 128.

Error (142): "The number of low latency external measurements (140) exceeds the limit supported by eHS Gen 5 x128. "+ "The maximum number of low latency external measurements allowed in the circuit is 128. Try to reduce the number of [Surge Arrester] components in your circuit."

Error (143): A parameter has an expression value that could not be resolved.

• Block 'vsrc1'

• Unable to evaluate 'dc_value * 0.5' in Matlab

Error (144): The feature "eHS Gen 5" has been improved and requires to update eHS Gen 5 to version 1.2.0. Update to a firmware which contains a newer version of the block to use this feature.

Error (145): The Solver Strategy "Smallest Time Step" can't be apply on this circuit. Using the "Lowest Latency" strategy in the Schematic Editor will solve this issue but will increase the Time step of the circuit."

Error (146): The Schematic Editor model has unsaved changes. Save the model before loading the circuit.

Error (147): The name “reset” is reserved for a utility pin. Change the name in the circuit model.

• Reserved names: “parameter_set_id”, “parameter_set_output_id”, “reset”

Error (148): Cannot read resource file “Pun File”. Parser had the following issue:

Cannot find ‘poles impedance’ in ' 3.804409763194375955D-07 1.494890152734087937D-05 3.348494529259195805D-05 '

Invalid propagation section

Invalid mode section 1

Error (149): Frequency dependent line “fd1” has 3 phases, which doesn’t match the configuration file “Pun File” that has 6.

Error (150): The number of Frequency Dependent Line total phases (18) exceeds the limit. The maximum number of Frequency Dependent Line phases is 16.

Error (151): The current time step (4000 ns) is invalid with the current frequency dependent lines.

Minimum time step is 10 ns, maximum time step is 2225 ns.

You can try splitting the longest frequency dependent line in smaller segments.

Error (152): Trying to connect signal "Omega_r" of component "pmsm1" to CPU or IO but no matching signal information was found in selected firmware description. Regenerate ioconf to make sure firmware description file is up to date with features available in Schematic Editor.