Description

The constant parameter (CP) line model assumes that the line parameters R, L, and C are independent of the frequency effects caused by the skin effect on phase conductors and on the ground. The model considers L and C to be distributed (ideal line) and R to be lumped at three places (R/4 on both ends and R/2 in the middle). The shunt conductance G is taken as zero. The frequency dependence of the line parameters (represented in the FD model) is an important factor for the accurate simulation of waveform and peak values. However, the CP model is very robust, simple, and fast. It also provides a good alternative for a first approximation analysis.

A transposed or untransposed CP line is represented by a) its sequences, or b) its propagation modes and the transformation matrix (Ti) between mode currents and phase currents. Implementation details can be found in [1].

Table of Contents

Mask and Parameters

General Parameters

Name	Description				Unit	Variable = {Possible Values}

Name	Description			Unit	Variable = {Possible Values}
Description	Use this field to add information about the component				Description = {'string'}
EMTP (.pun) file for line parameters calculation	The location (path) of the EMTP file (pun file) containing the line parameters				File = {'path.name'}
L-C units in EMTP (.pun) file	The units from the pun file can be taken using two options				L-C units = { 0, 1}
	mH/km, uF/km {0}		Inductance (L), capacitance (C)
	Ohm/km, uS/km {1}		Inductive reactance (Xl) and capacitive susceptance (1/Xc)
Line Length	The length of the line			km	length = {0, 1e64}
R	Per unit length resistance for each phase (mode)			Ω/km	R = {'-1e64, 1e64'}
L	Per unit length inductance for each phase (mode)			H/km	L = {'-1e64, 1e64'}
C	Per unit length capacitor for each phase (mode)			F/km	C = {'-1e64, 1e64'}
Base power (perPhase)	Base value for PU conversion			MVA per phase	pBase = { [1, 1e64] }
Base voltage (rmsLN)	Base value for PU conversion			kV rms LN	vBase = { [1, 1e64] }
Base frequency	Base value for PU conversion			Hz	fBase = { [1, 1e64] }
Continuously transposed line	Transposition (Untransposed/Transposed)				transp = { 0, 1}
	No {0}	Untransposed line
	Yes {1}	Transposed line
Transformation matrix	Transformation matrix between mode current and phase current ([Iphase] = [Ti] x [Imode]); not used in the case of transposed line.				Ti = { [-1e64, 1e64] }

Ports, Inputs, Outputs and Signals Available for Monitoring

Ports

This component supports a 4-phase transmission line

Name	Description

Name	Description
net_1_1	Network connection of phase 1 left (+) side
net_1_2	Network connection of phase 1 right side
net_2_1	Network connection of phase 2 left (+) side
net_2_2	Network connection of phase 2 right side
net_3_1	Network connection of phase 3 left (+) side
net_3_2	Network connection of phase 3 right side
net_4_1	Network connection of phase 4 left (+) side
net_4_2	Network connection of phase 4 right side

Inputs

None

Outputs

None

Sensors

At acquisition, the signals available by the sensors are:

Name	Description	Unit

Name	Description	Unit
V_Node(1,2,3,4)_(1,2)	Bus voltage for each phase (1,2,3,4)	V
I(1,2)_Node(1,2,3,4)_(1,2)	Current for each phase (1,2,3,4)	A
P(1,2)_Node(1,2,3,4)_(1,2)	Active power for each phase (1,2,3,4) on bus (1,2)	W
Q(1,2)_Node(1,2,3,4)_(1,2)	Reactive power for each phase (1,2,3,4) on bus (1,2)	VAR

The (1,2) in the previous table indicates the name of the bus at each end of the line (1 for the left (+) side and 2 for the right side)

Electrical Parameters

Calculation of electrical parameters

The Electrical parameters of CP lines can be calculated by using the https://opal-rt.atlassian.net/wiki/spaces/PDOCHS/pages/149979487 .

Reference

H. W. Dommel, "Digital computer solution of electromagnetic transients in single and multiphase networks," IEEE Trans. Power App. Syst., vol. pas-88, pp. 388-99, 04/ 1969.

HYPERSIM Documentation

Constant Param, 4-ph