Documentation Home Page ◇ HYPERSIM Home Page
Pour la documentation en FRANÇAIS, utilisez l'outil de traduction de votre navigateur Chrome, Edge ou Safari. Voir un exemple.
Constant Param, 3-ph
Description
The constant parameter (CP) line model assumes that the line parameters R , L, and C are independent of the frequency effects caused by the skin effect on phase conductors and on the ground. The model considers L and C to be distributed (ideal line) and R to be lumped at three places (line ends R/4 and line middle R/2). The shunt conductance G is taken as zero. The frequency dependence of the line parameters (represented in the FD model) is an important factor for the accurate simulation of waveform and peak values. However, the CP model is very robust, simple, and fast. It also provides a good alternative for a first approximation analysis.
A transposed or untransposed CP line is represented by a) its sequences, or b) its propagation modes and the transformation matrix (Ti) between mode currents and phase currents.
Implementation details can be found in:
H. W. Dommel, "Digital computer solution of electromagnetic transients in single and multiphase networks," IEEE Trans. Power App. Syst., vol. pas-88, pp. 388-99, 04/ 1969.
Mask and Parameters
General Parameters
Name | Description | Unit | Variable = {Possible Values} | |||
---|---|---|---|---|---|---|
Description | Use this field to add information about the component | Description = {'string'} | ||||
EMTP (.pun) file for line parameters calculation | The location (path) of the EMTP file (pun file) containing the line parameters | File = {'path.name'} | ||||
L-C units in EMTP (.pun) file | The units from the pun file can be taken using two options | L-C units = { 0, 1} | ||||
mH/km, uF/km {0} | Inductance (L), capacitance (C) | |||||
Ohm/km, uS/km {1} | Inductive (Xl) and capacitive (Xc) reactances | |||||
Line Length | The length of the line | km | length = {0, 1e64} | |||
R | Per unit length resistance for each phase (mode) | Ω/km | R = {'-1e64, 1e64'} | |||
L | Per unit length inductance for each phase (mode) | H/km | L = {'-1e64, 1e64'} | |||
C | Per unit length capacitor for each phase (mode) | F/km | C = {'-1e64, 1e64'} | |||
Base power (perPhase) | Base value for PU conversion | MVA per phase | pBase = { [1, 1e64] } | |||
Base voltage (rmsLN) | Base value for PU conversion | kV rms LN | vBase = { [1, 1e64] } | |||
Base frequency | Base value for PU conversion | Hz | fBase = { [1, 1e64] } | |||
Continuously transposed line | Transposition (Untransposed/Transposed) | transp = { 0, 1} | ||||
No {0} | Untransposed line | |||||
Yes {1} | Transposed line | |||||
Transformation matrix | Transformation matrix between mode current and phase current ([Iphase] = [Ti] x [Imode]); not used in the case of transposed line. | Ti = { [-1e64, 1e64] } |
Line Generator
For more information see Line Generator
Ports, Inputs, Outputs and Signals Available for Monitoring
Ports
This component supports a 3-phase transmission line
Name | Description |
---|---|
net_1(a,b,c) | Network connection of phases (a,b,c) of the left (+) side |
net_2(a,b,c) | Network connection of phases (a,b,c) of the right side |
Inputs
None
Outputs
None
Sensors
At acquisition, the signals available by the sensors are:
Name | Description | Unit |
---|---|---|
V(a,b,c)_Node(1,2,3)_(1,2) | Bus voltage for each phase (1,2,3) | V |
I(a,b,c)_Node(1,2) | Current for each phase (1,2,3) | A |
The (1,2) in the previous table indicates the name of the bus at each end of the line (1 for the left (+) side and 2 for the right side)
Electrical Parameters
Calculation of electrical parameters
The Electrical parameters of CP lines can be calculated by using the Line Generator .
Propagation Delay
The propagation delay is calculated as follows:
Where i is for each of the phases, L and C stands for the inductance and capacitance of the line per unit length.
When the propagation delay is smaller than the time step in a transposed line, the Constant Param block is automatically replaced by an equivalent PI Line.
For any case, when a CP line is used the simulation time step should be larger than the propagation time of the line. When the propagation delay is smaller than the simulation time a message will appear in the console, here is an example:
If the line is transposed:
WARNING in line: <Name of Block>.
The propagation delay (X) is less than the sample time (Y). A PI line is automatically used.
WARNING in the model [<Name of Block>:]! The line type has changed and the results may be false. Please restart the simulation.
These messages indicate that the line model is automatically changed to a PI model. Since the model is changed, the user needs to restart the simulation (re-analyze and re-generate code).
If the line is untransposed:
WARNING in line: <Name of Block>.
The propagation delay (X) is less than the sample time (Y). A PI line is automatically used.
ERROR in line: <Name of Block>.
The propagation delay is less than sample time and the line is Untransposed.
A PI line cannot be automatically used. Use a PI line with matrix parameters.
These messages indicate that the model cannot be automatically changed because the line is untransposed. This happens because there are three distinct modes and the PI model only supports two. Thus, if the user wants to simulate a very short untransposed line, the user needs to use a PI line with the matrix parameters.
OPAL-RT TECHNOLOGIES, Inc. | 1751, rue Richardson, bureau 1060 | Montréal, Québec Canada H3K 1G6 | opal-rt.com | +1 514-935-2323
Follow OPAL-RT: LinkedIn | Facebook | YouTube | X/Twitter