HYPERSIM

Added

• Added support for MATLAB R2023a
• Added support for multiple Dashboards when having several HYPERSIM instances or models opened at the same time. See OPAL-RT Dashboards
• Added How To Example Model:
  • Examples | PSCAD Import IEEE 39-Bus System
• Added the following Python API commands:
  • the simulation mode option in the setTarget command
• Added PSSe Import Option
  • Added Group Machines With Controls option by default
• Added a notification in case of a simulation crash (limitation: feature not available on Red Hat 32-bit OS)
• Added Python 3.9 and 3.10 compatibility for DataLogger API modules
• Added Processor Performance information to the .simout
• Added ScopeView template in the FPGA scope example model

Improved

• Improved Impedance Measurement workflow
• Improved logging in the console with timing
• Improved message when requesting a license without network connection
• Improved missing license key not found error message
• Improved error message when 2 control output pins feed the same signal
• Improved validation of the topology
• Improved time to build the topology

Fixed

• Fixed Target I/O Interface component not renaming pins containing certain forbidden characters on the schematic

• Fixed issue with Target I/O Interface component when a data point is lost
• Fixed simulation still running on the target in case of an engine crash on the host (limitation: fix not available on Red Hat 32-bit OS)
• Fixed sh: /sbin/lspci: No such file or directory error in the target diagnostic for OPAL-RTLinux OS
• Fixed eHS target license missing error
• Fixed HYPERSIM average simulation time value in .simout file
• Fixed HYPERSIM RTMonitor CPU "No Selected CPUs" error

Removed

• Removed HyperView Monitor tab
• Removed HyperView Line tab and moved it to corresponding Lines component masks
• Removed HyperView SyncMac tab and moved it to corresponding Synchronous machine with fault component mask
• Removed Sequence Manager for this version due to instabilities. It will be back in the next version

I/O Interfaces

C37.118 Slave

Improved

• Improved C37.118 example model with automatic synchronization interface detection

Fixed

• Fixed issue with the process not being migrated to the correct CPU core
• Fixed loss of connection issue with long simulations

OPAL-RT Board

Improved

• Added a pop-up to warn users that OP4200 support as MuSE remote target will no longer be supported as of HYPERSIM 2024.2

Fixed

• Fixed switching to a 64 port loadin/loadout bitstream not showing the correct configuration menu until the I/O Interface menu is restarted
• Fixed flashupdate unable to load dynamic libraries
• Fixed standard repository not finding default bistreams

OPC-UA Server

Fixed

• Fixed issue with the TCP server not attaching to the configured interface
• Fixed publish paths and allowed multiple datapoint names in different subfolders

Synchronization

Added

• Added possibility to apply an offset to the received timestamp before returning it to the model

TCP-UDP

Fixed

• Fixed issue with float and double-bit precision data types

FPGA-Based Simulation

Added

• Added support for the PMSM VDQ machine in eHS Gen5 VC707 firmware
• Added licensing management for eHS Gen5 and PADE5 discretization method
• Added new Induction Machine with Saturation model
• Added support for single switches in eHS Gen5 firmware
• Added capability to use User Defined Back EMF profile for PMSM and BLDC

Improved

• Improved reset logic of eHS to fix initial state at model startup
• Improved names of I/O connections to match Hardware Slot and Channel identification
• Improved Installer/Uninstaller performance
• Improved error message for malformed JSON resource file returning "Error (139)"

Fixed

• Fixed issue when connecting a measurement to multiple AO from different mezzanines
• Fixed issue when disconnecting some, but not all, gate connections from multi-level switching components (Half Bridge, Three-Level, Cycloconverter)
• Fixed Thyristor behavior in eHS Gen4
• Fixed issue preventing setting of rectangular Ldq matrices in PMSM VdQ
• Fixed PMSM Variable DQ parameter file that may contain different numbers of values along the direct and the quadrature axes

A more detailed list of release notes is available at C:\OPAL-RT\eFPGASIM\v2.13.2.61\Docs\ReleaseNotes\Releases_Notes.pdf