HYPERSIM

Added

• Added user guide to help EMTP users go to real-time with HYPERSIM

• Added Sequence Manager tool to record and manage test sequences from manual manipulations

• Added support for wound rotor in recently added Asynchronous Machine [The former induction machine models will be kept as Legacy]

• Added support for MATLAB R2020a and R2020b

• Added exciter library models:

  • IEEET2

  • IEEET3

  • IEEEVC

  • EXDC2

  • EXST1

  • EXST3

  • EXPIC1

  • SCRX

• Added governor library model:

  • WEHGOV

• Added stabilizer library model:

  • PSS2A

• Added example models :

  • Emergency Diesel-Generator, Asynchronous Motor and 25 Synchronism-Check 

  • Directional Overcurrent Protection

  • Type 4 Wind Farm model

  • EMTP Compatibility Introduction

  • EMTP IEEE 39Bus Benchmark

• Added a Data Name filter in the Sensor configuration view  to help accelerate I/O assignment

• Added options to rename and delete I/O Interfaces

• Added Sigcmp to Advanced Function Editor in ScopeView, allowing comparison of a test signal to a reference signal with a user-defined tolerance

• Added Time format option in the data logger file browsing with ScopeView, allowing easily shifting results to time = 0 in graphs

• Added support for EXAC3, IEEET1, HYGOV, SCRX, AC8B, PSS2A and WEHGOV in PSS®E import

• Added progress bar when importing PSS®E files

• Added progress bar on Apply/Ok of I/O interface modifications to better follow updates of large I/O configurations

• Added Python API function to rename devices

Improved

• Improved Python API command setComponentParameter, making it synchronous, thus removing the need to add wait time after its call

• Improved PSS®E import to skip buses with IDE=4 and all components connected to them

• Improved PSS®E import to manage multiple sources (machines or voltage sources) on the same bus; the biggest source (the one with highest PT value in PSS®E) stays as is, whereas the smaller ones are connected through an intermediary resistor and their type is changed to PQ

Fixed

• Fixed inconsistencies in tooltips of Network component forms

• Fixed unit of winding voltages for Saturable 2-winding transformer with tap changer that wasn't set to rmsLL like other transformers in the previous version

• Fixed issue where HYPERSIM would not start properly on a completely new Windows installation because of missing Microsoft libraries

• Fixed various issues with In1, Vt and Vc1 pins and the lower limit of exciter ST1A

• Fixed issue in AC3A exciter form where diagram would show Voel

• Fixed voltage source base voltage display value

• Fixed issue where sensor changes could be detected even if no changes were executed

• Fixed issue during uninstallation where some documentation files would remain

• Fixed occasional crash of a model engine when opening the Netlist after a specific sequence of actions

Removed

• Removed automatic generation of the EXata CPS files when opening I/O Interface

I/O Interfaces

C37.118 Slave

• Fixed issue when sensors of a given slave are dispatched on different cores

• Fixed missing editable slave name in I/O Interface configuration

DNP3

• Fixed possible crash of asynchronous process with certain configurations

IEC 61850

• Fixed UI crash when .icd file parsing failed

Modbus Slave

• Fixed issue with initial values and float data types

• Improved automatic setting of ID for TCP slaves

OPAL-RT Board

• Fixed issue where the FPGA bitstream could be reprogrammed twice upon starting the simulation

OPC UA Server

• Fixed Advanced Options which where showing at the root of the I/O Interface instance rather than in other elements of the tree

FPGA-Based Simulation

• Added support of release notes in firmware description

• Added 1st order low pass filter on PMSM VDQ PQ measurements

• Added support of native SFP link on all firmware to allow multi-FPGA configuration

• Fixed format of angle of PMSM VDQ FPGA module

• Fixed issue on second machine of Dual PMSM Motor Vdq with park transform, rotor offset and initial angle parameters